Cleaning 50s

[Fiddy Rider]

Hey guys what do you use to cover your carby or airfilter when cleaning your 50??? What else do ya use to get it real claen?? Thanks

[rideforlife69]

i wouldnt have a clue but try a plastic bag. and for cleaning use degreser and wash it off and washing powder works 2 or u can get proper bike gel cleaning shit from bike shops.

easter

[Fiddy Rider]

Yeah I know how to do it just wondering what others use!!!

[OZ FMX]

i just use a snall plastic bad over the filter then tie it on there with a rubber band around where the filter boot meets the carb

washing wise i give it a good og over with degreaser then a go over with CT18 or CT20 truck wash and let it sit for about 10-15 min rinse and your done

[click_click]

i take the airfilter off and stuff the hole with rags and cover that with a small lunch bag

[skywalker]

i just spray the filter with the hose.

gets it clean. :) hahahaha

[2Stroker]

i cover my air filter with a plastic bag the like tape it up with soem stiocky tape and with my zorst i put a plug or some stuff in it cause i dont want any water gettiin in ya zorst. also i just use me high pressure cleaner gets her spankin

[eichkay]

I just get out the GMC presure cleaner i got for $50 and try and aviod blasting the carbi and steer clear of the exhaust , When i can be bothered i find a plastic bag and just wrap it around the air filter.

Then get some 5 paper towels and wipe the dirty water droplets off the bike

[sik_50]

yerp i do pretty much the same, little plastic bag over the filter clip it up wrap a rubber band round it a couple of times. and i just stuff a rag in the exhaust LOL.

[2Stroker]

do u guys run your bikes after u have washed them cause ive been told that its bad if ya dont. i let mine run, heat up a bit just to evaporate any water round the plug n stuff

[eichkay]

Yeah i run my bike after cleaning. Just in case i get water where it aint spose to be, Also go over bearings and stuff with CRC to remove water and stop it gathering and rusting my bike up.

Also get my bike on the compresion stroke to close up the valves befor i clean or transport the bike

[Fiddy Rider]

I don't usually run mine after I wash it, probably should but! I do spray some water despercent on the steel parts and on the motor! I just put a muffler bung in the exast and a plastic bag and a zip tie over the carby and remove the filter. I also give my chain a real good scrubing to get it nice and clean!!

[DoorMatt]

yeh i do the same with the plastic bag over the filter. and as fo claning it, i use car wash because it doesnt damage the anodising on my rims. and yeh i shuv a bit of rag in the xaust.

[rm_ash_80_125]

yer i just get a frezzer bag and cable tie it to the air fliter then put a cork up the exust. and i start it rite after a was

[attard]

Yea i take off my filter, cover the hole of my carby with duct tape and plug up the pipe plus i take the seat and plasics off as well then spray the Frame motor,chain and wheels with kero than get the presure cleaner out and blow all that off than get my bucket of warm soapy water and give her a sponge than rince it of with a hose than get out the air compresser and blow all the water off every where than get the wd out and do all the bearings,leavers,pegs and gear leaver plus the chain than get out the silo spray out and get her glieaming than i take the carby off and clean it out because u still get a little water in it from where the cable go's in.
Thats for my 50, dont ask me what i do to my 250 because i will be hear all day.LOL!!!!! :Z440: